日本国产三级在线视频_少妇苏霞的沉沦_国产乱子伦午夜精品视频_啦啦啦免费高清在线观看7_国产精品视频更新_亚洲精品国产男女猛烈_三级片网站视频_精品免费久久久久久久_59pao成国产成视频永久免费

Support

Connecting MX100G-S SIP-ISDN Gateway to Elastix

New Rock’s MX100G-S SIP-ISDN Trunking Gateway with T1/E1 ports is compatible with with the open-source software Elastix® for unified communication solutions.

Scenario

The MX100G-S SIP ISDN gateway and Elastix® are in the same LAN. A static IP address 192.168.250.99 is set for MX100G-S gateway and a static IP address 192.168.250.222 is set for Elastix®.
In this application note, two most common applications and their related configurations are described, including:
- Peer to Peer mode (without registration)
- Registration mode
After the following configurations (either peer to peer mode or registration mode), the gateway can route the calls from Elastix® to ISDN for outbound, and can direct the incoming calls from ISDN to AA system of Elastix® via ISDN, then an IVR prompt will be announced to ISDN, then callers on ISDN side can dial extension numbers after they heard the IVR prompt.

Peer to Peer mode (Without Registration)

Configuration on Elastix®

1. On PBX > PBX Configuration > Trunks page, click Add SIP Trunk to add a SIP trunk.

2. Fill in Trunk Name for both General and Outgoing Settings.

3. Fill in PEER Details (host = FXO gateway IP address; type=account type) on Outgoing Settings as follows:
host=192.168.250.99

type=peer

4. On PBX > PBX Configuration >Inbound Routes page, fill in DID Number (it can be any number, please remember it, for you will use it when you configure the gateway).

5. Choose IVR in Set Destination.

Configuration on MX100G-S Gateway

1. On Basic > SIP page, fill in Elastix® IP address in the Proxy server field.

2. On Routing > Routing Table page, fill in routing rule shown as below (Suppose MX100G-S has 1 E1 port) for directing calls from Elastix® to ISDN: IP X ROUTE ISDN 1.

3. On ISDN > ISDN 1, make sure Status is Link up in ISDN layer and Status is In Service in ISDN-D channel.

4. On Route > Routing Table, fill in routing rules shown as below for incoming call forward to Elastix®:
ISDN x REPLACE 8888

ISDN x ROUTE IP 192.168.250.222:5060

Dialing Method

- For making calls from ISDN to Elastix® through MX100G-S gateway, the caller dial the number of ISDN line connected to gateway’s E1 port, then dial the extension number of Elastix® after hearing the IVR.
- For making outgoing calls from Elastix® extensions, the extensions directly dial the outside number.

Registration Mode

Configuration on Elastix®

1. On PBX > PBX Configuration > Trunks page, click Add SIP Trunk to add a SIP trunk.

2. Fill in Trunk Name for both General Settings and Outgoing settings.

3. Fill in PEER Details (host = MX100G-S gateway IP address; username=SIP account; secret=password; type=account type) on Outgoing Settings as follows:
host=192.168.250.99
username=test
secret=abc123

type=friend

4. On PBX > PBX Configuration > Inbound Routes page, fill in DID Number (it can be any number, please remember it, for you will use it when you configure the gateway).

5. Choose IVR in Set Destination.

Configuration on MX100G-S Gateway

1. On Basic > SIP page, set Elastix® IP address 192.168.250.222 as registrar server and proxy server, fill in User name and Password (the same as the username and the secret in Elastix®).

2. In ISDN > ISDN 1, make sure Status is Link up in ISDN Layer and Status is In Service in ISDN-D channel.

3. In Routing > Routing Table, fill in routing rules to direct incoming calls from IDSN to Elastix®. (Because 8888 is the inbound number of Elastix®, so here it will replace the calling party number to 8888 send to Elastix® and go to the Elastix®’s IVR )